Last week when removing a parcel off the back (Drivers side) seat, I happened to notice that the door seal (Not the one on the actual car door, but the seal that surrounds the door aperture) had developed a distinct "wave" along the top. The actual rubber seal was moving away from the body framework. The same was happening to all door seals.

Took my 10MY in for it's 2nd service yesterday. Mentioned it when I arrived there.

All 4 door seals are being replaced under warranty. Taking it back next week for fitting.

So, anyone with a Freely that's still under warranty check the door seals.

I'll check mine before the warranty runs out. Thanks for the heads up.  Poke it, Poke it, make it do it again!!

Gone - 2008 Freel2 HSE Santorini Black
Hello - 2010 RRS TDV6 3.0 HSE Santorini Black

I need to have a look too

Any photo showing what your is like to compare?

On my car one rear door only. It's not the main body opening seal but a narrow stuck on one on the right of the photo, mine has started to detach itself and deform, no big deal until I have to go to the dealer next.

[/img]


Here's what it looks like.

Have tried punching it back up with the back of your hand or fist, i'm sure they fit into a groove around the door frame a bit like how the wheel arch rubbers fit into position.

Yes, I've pushed them back into the original position, but after a couple of days they distort again.

My initial thoughts are that the seals are slightly over-sized, hence the distortion.

They wont be oversize, you have to make sure they are knocked on well into the corners first as that is where they are likely to pull away to begin with if anywhere, use a rubber mallet.

Mona Geeza wrote:

use a rubber mallet.

especially around the sunroof area  2002 Honda VFR800
2002 Toyota Celica 140 Silver (mid life crisis - again!)
2007 FL2 GS Manual Army Reconnaissance Green + freel2.com sticker
2004 Toyota Celica 140 Black - Gone
2000 Toyota Celica 140 Silver - Gone
1998 Toyota Celica ST Pearl Green - Gone
1996 Nissan Primera 1.6 - Gone
1994 Rover Montego 1.6 Auto - Gone

Mines peeling away on the front passenger door, they are just stuck on with narrow foam body tape......back to the dealer I go!! 2013 FL2 - Black Edition Auto
2013 FL2 - Black Edition Manual GONE!
Founder of the 'Microscopic LR Spoiler Badge Club'
Destroyer of chrome rears.....

New here so please excuse any naivety!

Looks like I've got to replace the nearside rear body door seal on my just-acquired FL2 as it looks like a dog has chewed it!

If anyone has done this - replaced one not chewed it! - and can provide any pointers then most appreciated.

Seems the original part no. is LR001631? A few breakers list them but is it really worth having a used one?

Thanks.

Pull the old one off, line up the new one so the centre gripper part is over the body seam, then push the new one on working your way around the frame, easy.
It's literally a 2 minute job to change the door seal. 2009 Rimini Red SE TD4. Soon to be sold.
Hyundai Ionic 5 Ultimate on order.
Gone. 2006 Tonga Green i6 HSE.

Thankyou Nodge - easy change as you said. I bought a new old stock seal from ebay for little more than scrappers were selling them for.

Thanks for letting us know the fix worked.

I have just replaced my drivers door on body, not door, seal. £50!
Free next day delivery, if you are a prime member.

Do a search on Amazon for Door Weatherstrip Seal Replacement For Freelander MK2 2006-2014 (on body) LR001630.

You will need an hacksaw to cut to length as there is some internal steel wire to cut.
Use a large rubber hammer you will know its located as the tone changes.