Freel2.com - View topic - Just had FL2 Clutch replaced


Forum-Gallery-Shop-Sponsors « Advertise on Freel2.com

Home · FAQ · New Posts · My Posts · PMs · Search · Members · Members Map · Calendar · Profile · Donate · Register · Log In

Home > Technical > Just had FL2 Clutch replaced - pressure plate fault?

Page 1 of 1

Print this entire topic ·

dorsetfreelander

Member Since: 20 Jul 2013
Location: Dorset
Posts: 4341

2014 Freelander 2 SD4 XS Auto Loire Blue

Just had FL2 Clutch replaced - pressure plate fault?

I thought people might be interested, I have a 10 reg FL2 with 44k miles, the clutch started slipping recently so I have just had it replaced for £685 at an independent LR specialist (the dual mass flywheel looked OK so left in place) The interesting thing is that the plate itself doesn't look worn too much to me (although I don't know how thick a new one is) so I guess it must be a weak pressure plate problem. Any views ?

incidentally the components have Ford Motor Company stamped on them, Since it's the same engine as a Transit van I wonder if the Ford items are cheaper than landRover?

Last edited by dorsetfreelander on 1st Nov 2013 5:58 pm. Edited 2 times in total

30th Oct 2013 8:11 pm

tim_roberts

Member Since: 10 Aug 2013
Location: Bournemouth
Posts: 215

2010 Freelander 2 TD4_e S Manual Santorini Black

In the top photo, it looks like one of the 'springy fingers' is bent. That would definitely cause slippage.

31st Oct 2013 7:31 am

rchrdleigh

Member Since: 18 Aug 2007
Location: Somewhere in the East of England
Posts: 1601

2011 Freelander 2 TD4 XS Manual Baltic Blue

The Freelander uses a Peugeot DW12 engine which is built for LR by Ford. The Transit engine is a Ford TDCi Duratorq engine, sometimes also referred to as a Puma engine and is used by LR only in the Defender.

31st Oct 2013 10:34 am

Steve D

Member Since: 19 Jan 2013
Location: Essexshire
Posts: 4092

tim_roberts wrote:
In the top photo, it looks like one of the 'springy fingers' is bent. That would definitely cause slippage.

I though that at first too but on closer inspection you can see that that's not one of the diaphragm fingers - if you look in the bottom picture you can see that it is part of the clutch pressure plate body and there's 3 of those 'fingers'. Past: FL2 TD4 HSE Auto
Evoque SD4 Dynamic Lux Auto
Present: Audi A3 S Line.

31st Oct 2013 11:36 am

tenet

Member Since: 23 Jul 2009
Location: cotswolds
Posts: 1072

2015 Freelander 2 SD4 SE Auto Orkney Grey

Is there any oil contamination present?? MY 09 GS manual in Lago Grey, Wood Co arm rest and side bumper strips - now sold.

MY 15 SD4 SE Auto Orkney Grey with colour coded Bumper Door Mouldings

31st Oct 2013 12:43 pm

Pegleg

Member Since: 15 Apr 2010
Location: Deep in mid Wales
Posts: 3114

2008 Freelander 2 TD4 GS Manual Santorini Black

Doesn't look worn to me either.
Wonder if the auto adjuster had stuck?

Is your clutch okay now? Another member of the failed FL2 clutch/DMF club, twice.

31st Oct 2013 4:09 pm

dorsetfreelander

Member Since: 20 Jul 2013
Location: Dorset
Posts: 4341

"Is your clutch okay now?"

Yes it seems fine now. Previously it would be OK and only slip in 6th if you floored it, then other times t would happen in 3rd. The clutch was also working right at the top of the pedal travel. How would I tell if the "adjuster" had stuck? I assume you are referring to the slave cylinder.

31st Oct 2013 4:42 pm

Pegleg

Member Since: 15 Apr 2010
Location: Deep in mid Wales
Posts: 3114

Not the slave cylinder.
There is a mechanical adjuster which automatically takes up wear on the friction plate. They have been known to stick due to clutch dust causing slip Another member of the failed FL2 clutch/DMF club, twice.

31st Oct 2013 5:26 pm

dorsetfreelander

Member Since: 20 Jul 2013
Location: Dorset
Posts: 4341

tenet wrote:
Is there any oil contamination present??

No everything looks fine. no sign of oil leakage. Could this be down to the pressure plate loosing some of it "umf" so that it no longer grips so well?

31st Oct 2013 5:44 pm

dorsetfreelander

Member Since: 20 Jul 2013
Location: Dorset
Posts: 4341

I have just had a very careful look at the pressure plate and there are signs of the moving part scratching. In the first picture there is some clearance around the sticking up bit but three of the six have signs of some rubbing. I wonder if that is enough to stop the pressure plate returning to the "bite" position fully? This looks like a manufacturing fault.

Click image to enlarge

1st Nov 2013 5:55 pm

Page 1 of 1

All times are GMT + 1 Hour

< Previous Topic | Next Topic >

Posting Rules

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum