| Author |
Message |
 Freelander 2 Does not go when you press the pedal |
Jagracer
 27th Jan 2022 2:48 pm
|
Forum: My Freelander 2 · Replies: 25 · Views: 12722 · Subject: Freelander 2 Does not go when you press the pedal |
| HI, most auto boxes I have had over the years are programmed to put the engine in Safe Mode to take loading off, and allow the Transmission Fluid to cool below a certain threshhold. Modern gearboxes n ... |
| p1295-11 reduced engine performance |
Jagracer
10th Nov 2021 9:07 pm
|
Forum: Technical · Replies: 42 · Views: 14824 · Subject: p1295-11 reduced engine performance |
| Thats good, hope all goes well for you now. |
| p1295-11 reduced engine performance |
Jagracer
10th Nov 2021 1:47 pm
|
Forum: Technical · Replies: 42 · Views: 14824 · Subject: p1295-11 reduced engine performance |
| Hi, the Injectors need to be manually coded to the ECU, they do not do it themselves. The earth lead goes to the top starter motor bolt on the bell housing where the starter motor bolts on. The usual ... |
| p1295-11 reduced engine performance |
Jagracer
9th Nov 2021 8:27 pm
|
Forum: Technical · Replies: 42 · Views: 14824 · Subject: p1295-11 reduced engine performance |
| The Injectors need to be coded to the car. Each one has a unique code number stamped on it. Number one is the flywheel end. The engine will not run properly until the codes are entered. There was a re ... |
| Back to a PC after years in the wilderness? |
Jagracer
9th Nov 2021 7:44 pm
|
Forum: Off Topic · Replies: 15 · Views: 6583 · Subject: Back to a PC after years in the wilderness? |
| For a work around, see this months Computer Active magazine (Nov 2021) for a way to get Windows 11 on your unsupported computer. |
| can anyone explain this please |
Jagracer
9th Nov 2021 7:41 pm
|
Forum: General · Replies: 4 · Views: 1704 · Subject: can anyone explain this please |
| You want 224DT 150 ps usually unless its a petrol 3.2. |
| Creaky rear end |
Jagracer
9th Nov 2021 7:38 pm
|
Forum: Technical · Replies: 9 · Views: 4287 · Subject: Creaky rear end |
| Hi, a word of warning, we had a noisy back end on our 2009 FL2. It also chirped a bit and the clutch appeared to slip at times. It also jumped around a bit on left hand corners. It cost us a new diff ... |
| Alarm display |
Jagracer
9th Nov 2021 7:33 pm
|
Forum: Technical · Replies: 7 · Views: 2623 · Subject: Alarm display |
| Hi, I did come across a recall to change the brushes in the pump motor the other week on the Haldex. Apparently there was a batch with weak springs that stop the brushes wearing down far. |
| Pulsating vibration and (?) bad struts? |
Jagracer
7th Nov 2021 6:11 pm
|
Forum: Technical · Replies: 5 · Views: 2467 · Subject: Pulsating vibration and (?) bad struts? |
| Just a thought, have you tried swapping the wheels left to right? If the offset is different it will show by swapping. The back end was all over the place on our 2008 car, and needed two Bilstein stru ... |
| Pulsating vibration and (?) bad struts? |
Jagracer
7th Nov 2021 11:02 am
|
Forum: Technical · Replies: 5 · Views: 2467 · Subject: Pulsating vibration and (?) bad struts? |
| I think you need to change the wheel bearing and all the linkage bushes as well as the rear struts. Make sure that the top strut bearing is sound as well, often forgotten. You might want to change the ... |
| Timing belt/chain |
Jagracer
29th Oct 2021 11:54 am
|
Forum: Technical · Replies: 39 · Views: 22445 · Subject: Timing belt/chain |
| Hi, if you take the gearbox out, the gap is about 20mm, so the bending moment is not too bad on a very high tensile heat treated ground dowel. I checked the dowel was straight after putting 300 foot p ... |
| Timing belt/chain |
Jagracer
29th Oct 2021 10:49 am
|
Forum: Technical · Replies: 39 · Views: 22445 · Subject: Timing belt/chain |
| Hi, I released the centre bolt with a Dewalt impact nut runner. The Dual Mass flywheels have a set of Torque Straps that operate in tension one way, ie, in the direction of Crank Rotation. You are rig ... |
| Timing belt/chain |
Jagracer
29th Oct 2021 10:16 am
|
Forum: Technical · Replies: 39 · Views: 22445 · Subject: Timing belt/chain |
| Hi, the secondary locking tool is a fail safe idea. I use a Dormer 8mm drill shank (the parallel end) as a dowel. I also have lengths of Tool Steel and Tool Steel Dowels in my toolbox. A 12.9 8mm bolt ... |
| Goes into limp mode when driving in the rain |
Jagracer
26th Oct 2021 9:04 pm
|
Forum: General · Replies: 3 · Views: 1496 · Subject: Goes into limp mode when driving in the rain |
| I have a problem 2008 model. The rain gets into the loom behind the battery tray into the fuse box behind the glove box inside. I would check the rain sensor as well as it only happens when it senses ... |
| traction light flashing |
Jagracer
26th Oct 2021 11:58 am
|
Forum: General · Replies: 4 · Views: 2357 · Subject: traction light flashing |
| Hi, I had a "slipping clutch" turned out to be the Bevel Box, and the rear diff damaged by a sticky handbrake. Your Autobox fault might have been the same problem as you have the right fault ... |
| |
