Forum-Gallery-Shop-Sponsors

« Advertise on Freel2.com
Home > In Car Electronics > Boot mounted auxiliary battery fitted.
Post Reply  Down to end
Page 1 of 1
Print this entire topic · 
ozjeff62



Member Since: 28 May 2018
Location: Sydney, NSW
Posts: 494
Australia 2011 Freelander 2 SD4 SE Auto Ipanema Sand
Boot mounted auxiliary battery fitted.

Well I knocked this project off this weekend.

Routed the cable out of the boot under the left rear seat, under the sill trims and through the firewall using the bonnet release cable port.

Everything is awfully tight in there, I damaged about four trim scrivets.

Greatest luck though, stuck a coathanger down the firewall and it accidentally went through the bonnet release hole. That could have been many hours of mucking around.

The cable is 5 metres of 6B&S twin core, an ATEM VSR, a pair of 100A circuit breakers and Anderson plugs in the boot. Circuit breakers go on the positive cable as close as possible to each battery.

I used the secondary earth point at the front. I don't know why, but it was there.

I am the world's worst solderer it seems so I won't be surprised if it fails at some point. But now it's over i feel pretty ok.

Cheers. MY11 SD4 SE Auto
Post #380337 27th Oct 2019 1:06 pm
View user's profile Send private message View poster's gallery Reply with quote
ozjeff62



Member Since: 28 May 2018
Location: Sydney, NSW
Posts: 494
Australia 2011 Freelander 2 SD4 SE Auto Ipanema Sand

 MY11 SD4 SE Auto
Post #380338 27th Oct 2019 1:07 pm
View user's profile Send private message View poster's gallery Reply with quote
ozjeff62



Member Since: 28 May 2018
Location: Sydney, NSW
Posts: 494
Australia 2011 Freelander 2 SD4 SE Auto Ipanema Sand

 MY11 SD4 SE Auto
Post #380340 27th Oct 2019 1:10 pm
View user's profile Send private message View poster's gallery Reply with quote
ozjeff62



Member Since: 28 May 2018
Location: Sydney, NSW
Posts: 494
Australia 2011 Freelander 2 SD4 SE Auto Ipanema Sand

 MY11 SD4 SE Auto
Post #380341 27th Oct 2019 1:12 pm
View user's profile Send private message View poster's gallery Reply with quote
ozjeff62



Member Since: 28 May 2018
Location: Sydney, NSW
Posts: 494
Australia 2011 Freelander 2 SD4 SE Auto Ipanema Sand

 MY11 SD4 SE Auto
Post #380342 27th Oct 2019 1:14 pm
View user's profile Send private message View poster's gallery Reply with quote
ozjeff62



Member Since: 28 May 2018
Location: Sydney, NSW
Posts: 494
Australia 2011 Freelander 2 SD4 SE Auto Ipanema Sand

 MY11 SD4 SE Auto
Post #380343 27th Oct 2019 1:15 pm
View user's profile Send private message View poster's gallery Reply with quote
ozjeff62



Member Since: 28 May 2018
Location: Sydney, NSW
Posts: 494
Australia 2011 Freelander 2 SD4 SE Auto Ipanema Sand




Just like it left the factory. MY11 SD4 SE Auto
Post #380344 27th Oct 2019 1:17 pm
View user's profile Send private message View poster's gallery Reply with quote
Lightwater



Member Since: 21 Aug 2014
Location: Sydney Northern Beaches
Posts: 4721
Ukraine 2013 Freelander 2 2.0T SE Auto Fuji White

How are you holding the battery down?

I have strips of aluminium under the boot floor (unfortunately covered by insulation) to hold the fridge to the floor.

The one bolt which you can see is where the tyre is so it had to be as thin as possible so I used a very large washer with a countersunk M6 Allan bolt up through the floor so it's only about 2mm thick under the floor.

 Procrastination, mankind's greatest labour saving device!

Acoustic insulation ARB TPMS 3xARB air compressors After cooler Air tank On-board OCD pressure air/water cleaning Additional 50L fuel Carpet in doors ABE 2x1kg Waeco 28L modified fridge Battery 4x26ah Solar 120w Victron MPPT 100/20 DC-DC 18amps 175amp jumper plug Awning 6x255/60R18
Post #380348 27th Oct 2019 1:51 pm
View user's profile Send private message View poster's gallery Reply with quote
Simon J



Member Since: 27 Jul 2019
Location: Norn Iron
Posts: 695
2008 Freelander 2 TD4 XS Auto Rimini Red

What do you plan to use the battery for as that’s a lot of heavy duty cabling you’re using?
Post #380349 27th Oct 2019 1:58 pm
View user's profile Send private message View poster's gallery Reply with quote
Lightwater



Member Since: 21 Aug 2014
Location: Sydney Northern Beaches
Posts: 4721
Ukraine 2013 Freelander 2 2.0T SE Auto Fuji White

How I solder 175amp lugs, with two 120watt irons & half fill the lug with solder & also pre heat the wire with another iron. It's hard to get enough heat into 6awg wire but 2 irons make it easier.

Click image to enlarge
 Procrastination, mankind's greatest labour saving device!

Acoustic insulation ARB TPMS 3xARB air compressors After cooler Air tank On-board OCD pressure air/water cleaning Additional 50L fuel Carpet in doors ABE 2x1kg Waeco 28L modified fridge Battery 4x26ah Solar 120w Victron MPPT 100/20 DC-DC 18amps 175amp jumper plug Awning 6x255/60R18

Last edited by Lightwater on 27th Oct 2019 2:26 pm. Edited 1 time in total
Post #380351 27th Oct 2019 2:19 pm
View user's profile Send private message View poster's gallery Reply with quote
Lightwater



Member Since: 21 Aug 2014
Location: Sydney Northern Beaches
Posts: 4721
Ukraine 2013 Freelander 2 2.0T SE Auto Fuji White

If charging at 20 amps over 10 metres (there & back) that's 0.264 voltage drop. Procrastination, mankind's greatest labour saving device!

Acoustic insulation ARB TPMS 3xARB air compressors After cooler Air tank On-board OCD pressure air/water cleaning Additional 50L fuel Carpet in doors ABE 2x1kg Waeco 28L modified fridge Battery 4x26ah Solar 120w Victron MPPT 100/20 DC-DC 18amps 175amp jumper plug Awning 6x255/60R18
Post #380352 27th Oct 2019 2:25 pm
View user's profile Send private message View poster's gallery Reply with quote
MotionInc



Member Since: 17 Jun 2019
Location: North America
Posts: 1288
Canada 2008 LR2 i6 SE Auto Tambora Flame

Lightwater wrote:
How are you holding the battery down?


My exact thought when I saw the pic?
Post #380364 27th Oct 2019 4:07 pm
View user's profile Send private message View poster's gallery Reply with quote
ozjeff62



Member Since: 28 May 2018
Location: Sydney, NSW
Posts: 494
Australia 2011 Freelander 2 SD4 SE Auto Ipanema Sand

Lightwater wrote:
How are you holding the battery down?



Probably use webbing over and around the battery going through the tie down point behind it, although I haven't settled on the location/orientation yet, see how it works with the fridge in situ. MY11 SD4 SE Auto
Post #380385 28th Oct 2019 6:57 am
View user's profile Send private message View poster's gallery Reply with quote
Lightwater



Member Since: 21 Aug 2014
Location: Sydney Northern Beaches
Posts: 4721
Ukraine 2013 Freelander 2 2.0T SE Auto Fuji White

A few photos down this page of my custom fridge bracket. It's only 6mm thick so it is fixed in permanently. Maybe some ideas for a bracket for the battery.
https://www.freel2.com/forum/topic29388.html Procrastination, mankind's greatest labour saving device!

Acoustic insulation ARB TPMS 3xARB air compressors After cooler Air tank On-board OCD pressure air/water cleaning Additional 50L fuel Carpet in doors ABE 2x1kg Waeco 28L modified fridge Battery 4x26ah Solar 120w Victron MPPT 100/20 DC-DC 18amps 175amp jumper plug Awning 6x255/60R18
Post #380386 28th Oct 2019 7:44 am
View user's profile Send private message View poster's gallery Post Reply
Post Reply  Back to top
Page 1 of 1
All times are GMT + 1 Hour

Jump to  
<  Previous Topic | Next Topic >
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Site Copyright © 2006-2024 Futuranet Ltd & Martin Lewis
Freel2.com RSS Feed - All Forums


Switch to Mobile site