Forum-Gallery-Shop-Sponsors

« Advertise on Freel2.com

Home > Other Site Sponsors > GAP Diagnostic Announcement-2016-07-25-Apple App & More
Post Reply  Down to end
Page 1 of 1
Print this entire topic · 
PatGAPInnov
Site Sponsor


Member Since: 08 Sep 2014
Location: Montreal
Posts: 12

Canada 
GAP Diagnostic Announcement-2016-07-25-Apple App & More

Hello Everyone

First, we would like to thank all our customers, beta testers and the community for your continuous support. Many new additions were the results of your feedback and suggestions. We could not be where we are without you!

As many of you already know by now, a new App, version 2.9, for Apple devices was released over the week end. We’ve also released a new special firmware available for beta testers only at the current time. I will do a second post shortly showing each point in detail but here’s a resume of the new additions when using both the new App and firmware or using the new App only with an older firmware.

Top Bar (new and old firmwares): A new bar was added which shows the current connection and ignition status as well as battery voltage.



Faults function (new and old firmwares): Advanced Read
-Status bit flags default selection can be saved for future use
-Status bit flags are visible as icons on top of fault descriptors
-Status bits can be included in the exported emails



Height Adjust (new firmware only): A new and more intuitive screen to adjust your suspension height with default and saved settings. Contrary to our previous method, height changes are relative to the default height and not the current standard height.

0 -> 25: current height, 0 mm, or default in this example is shown on the left while the selected height setting (My offroad height in this example) is shown right, + 25 mm

Click image to enlarge


20 -> -10: current height, +20 mm relative to the normal height (0 mm), shown on the left while the selected height setting (Motorway in this example) is shown right, -10 mm relative to the normal height (0 mm).

Click image to enlarge


Click image to enlarge


Height Control (new firmware only): This function allows you to remotely control your current height (Access, Normal, Offroad) and lower both axles to the bumpstops.



Suspension Calibration (new firmware only):
-New manual calibration layout
-New guided calibration function. This unique method eliminates the need for calculations, even ground and requires only one iteration. The whole process takes 5 minutes.

Click image to enlarge


Guided calibration instructions:
• The first corner to be calibrated is the front left corner (1).
• Place your measuring tape as instructed and use the up and down arrows (2) to reach the required height (3).
• Once completed, click on Send (4). The next corner to be calibrated will now be high-lighted.
• Repeat the previous steps for all corners.

New Suspension Test Valve function layout (new firmware only)

Click image to enlarge


Live values:
-All live values (PIDs) are now available for all supported vehicles (L322: except for older BMW type ECUs, new firmware only)
-Trigger function which allows custom audible or vibration alarm and automatic start/stop logging of live values. (new and old firmwares)

Click image to enlarge


Trigger example:
• The live value increases and passes the Start target of 20 % (first red dotted line)
• Recording begins and the previous data is kept (2 seconds, as set)
• The Stop condition is met at around 6.5 seconds, hence the trigger indicator (red dotted lines)
• Recording continues for 4 seconds as set
• Enabling the Buzzer will generate a sound when the condition is met. Perfect when moni-toring live data. Can be used without using the automatic recordings feature.

-Favourite Fast Add feature which allows adding live values to favorite list quicker. (new and old
firmwares)



• Click on the star when viewing an ECU live values

Click image to enlarge


1- Click here to create a new list
2- Current favourite lists are shown here
3- Click on the star to add the live value to this favourite list


-Layout improvements (new and old firmwares)
-Selection of which live values to be exported and viewed (logs). (new and old firmwares)

Click image to enlarge


Car Configuration File (new and old firmwares):

-Complete CCF list can be edited upon request.
-Favourite Fast Add feature which allows adding configurations to favorite lists quicker.

ECU Info (new firmware only): This new layout is the basis for what will be the next step reflashing wise. It now shows which ECUs are up to date and those for which a newer version is available. If you are testing this function, please send us the results using the send e-mail button for our records. This will help us validate the automatic file selection algorithm.

Click image to enlarge


An historic of each ECU Info scan is saved and can be recalled.

Tool Activation (new and old firmwares): Initial activation of the IIDTool can all be done within the App when the mobile device is connected to the internet. Additional licences can also be entered in the App.

New French version (except for live values and car config, new firmware only)

Documentation: The user manual was completely overhauled and will be released in the comming days in French and English.

Jaguar support: It is now possible, upon request, to use the IIDTool BT or Pro on 2008 and up Jaguars.

Work on the Android App is still under way. If you are using Android devices only, please do not update to the special firmware 2434 (English), 2435 (French) or 3630 (Pro English), 3631 (Pro French) and up since the firmware is not backward compatible with earlier App versions. You can, however, revert back to the latest beta if Android usage is required after using it on an Apple device.

Our current beta testers using Apple devices can benefit from these new additions by updating the App to V2.9 and IIDTool firmware to:

BT:
-Special Build 2439 (English, French upon request)

Pro:
-Special Build 3643 (English, French upon request)

We strongly recommend updating your mobile device operating system (iOS) to the latest version prior to using the new App and firmware.

As usual, feedback is more than welcome! For those who are not currently beta testers and want to test the new App and firmware simply send us an e-mail or a PM.

Cheers Thumbs Up

Edit: Added pictures and additional comments.

Last edited by PatGAPInnov on 4th Aug 2016 9:01 pm. Edited 4 times in total

Post #303292 25th Jul 2016 7:07 pm
View user's profile Send private message View poster's gallery Reply with quote
Yorky Bob



Member Since: 28 Apr 2015
Location: Yorkshire
Posts: 4561

United Kingdom 2013 Freelander 2 TD4 GS Manual Firenze Red

Well all that went straight over my head. Yawn FL2 MY10 TD4 GS traded in at 2 years
FL2 MY13 TD4 GS Current

Post #303299 25th Jul 2016 9:47 pm
View user's profile Send private message View poster's gallery Reply with quote
PatGAPInnov
Site Sponsor


Member Since: 08 Sep 2014
Location: Montreal
Posts: 12

Canada 

Edited the first post, pictures added...

Post #303480 28th Jul 2016 9:42 pm
View user's profile Send private message View poster's gallery Reply with quote
adcooper



Member Since: 04 Nov 2016
Location: Halesowen
Posts: 3

United Kingdom 2011 Freelander 2 SD4 HST Auto Ipanema Sand

Very tempted to get one for our FL2

Post #311837 23rd Nov 2016 12:04 pm
View user's profile Send private message View poster's gallery Reply with quote
cqr



Member Since: 05 Mar 2013
Location: kent
Posts: 1301

England 2008 Freelander 2 TD4 XS Auto Stornoway Grey

How many £££s are these 2008 xs
Snorkel
raised axle/gearbox breathers
Mantec tank guard
Cb radio
Blanked EGR
Sump guard
Scratches
Snolkle

Post #311853 23rd Nov 2016 5:43 pm
View user's profile Send private message View poster's gallery Reply with quote
alex_pescaru



Member Since: 12 Mar 2009
Location: RO
Posts: 4510

https://www.gap-diagnostic.com/shop/

Post #311866 23rd Nov 2016 9:00 pm
View user's profile Send private message View poster's gallery Reply with quote
Yorky Bob



Member Since: 28 Apr 2015
Location: Yorkshire
Posts: 4561

United Kingdom 2013 Freelander 2 TD4 GS Manual Firenze Red

IIDTool Pro £1,650.00 and on going fees. Maybe not. Whistle FL2 MY10 TD4 GS traded in at 2 years
FL2 MY13 TD4 GS Current

Post #311868 23rd Nov 2016 9:07 pm
View user's profile Send private message View poster's gallery Reply with quote
shiggsy



Member Since: 13 Jan 2013
Location: Kent
Posts: 716

United Kingdom 2007 Freelander 2 TD4 HSE Auto Baltic Blue

The Pro versions are not locked to a specific vehicle, the cheaper ones are VIN Locked to a single vehicle for the advanced functions, but the basic functionality can still read and clear faults on multiple vehicles.

cqr, I went up to Island 4x4 (outside Maidstone) and bought mine, its the BT (Bluetooth) Version it was £384 but that was a year ago.

http://www.island-4x4.co.uk/integrated-int...27303.html

( Note that their listed prices don't include VAT) 
Hung like Einstein, smart as a horse.

Post #311870 23rd Nov 2016 9:20 pm
View user's profile Send private message View poster's gallery Reply with quote
cqr



Member Since: 05 Mar 2013
Location: kent
Posts: 1301

England 2008 Freelander 2 TD4 XS Auto Stornoway Grey

Thanks, just ordered £210 worth from island 4x4
Timing belt kit etc 2008 xs
Snorkel
raised axle/gearbox breathers
Mantec tank guard
Cb radio
Blanked EGR
Sump guard
Scratches
Snolkle

Post #311874 23rd Nov 2016 10:03 pm
View user's profile Send private message View poster's gallery Post Reply
Post Reply  Back to top
Page 1 of 1
All times are GMT + 1 Hour

Jump to  
Previous Topic | Next Topic >
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Site Copyright © 2006-2021 Futuranet Ltd & Martin Lewis


Switch to Mobile site