Forum-Gallery-Shop-Sponsors « Advertise on Freel2.com

Home > Search

Author Message  Newbie timing belt question jimbowats 11th Jun 2025 5:19 pm Forum: Technical · Replies: 35 · Views: 1546 · Subject: Newbie timing belt question The angle amount is just a way for the manufacturer to guarantee a set torque value. Its probably the same as 150-200nm but for some reason the angle figure guarantees a nice tight bolt (not that 200n ...  EML and various faults. jimbowats 7th Jun 2025 2:41 pm Forum: Technical · Replies: 29 · Views: 2055 · Subject: EML and various faults. My FL2 has a bit of oil at the same location on that intercooler pipe also...weird the clamps are tight and no splits in the hose I can only assume under heavy boost it weeps a bit  2007 Freelander 2 rebuilt after timing belt failure no start jimbowats 6th Jun 2025 8:32 am Forum: Technical · Replies: 18 · Views: 972 · Subject: 2007 Freelander 2 rebuilt after timing belt failure no start Useful tip for the RAC man and any other freelander 2 Auto owners.... if the car won't start and you need to get it in neutral pry up the silver gear selector surround..(its just clipped in) , lif ...  Screeching noise between 15k - 18k near pulleys - 2014 TD4 jimbowats 2nd Jun 2025 8:17 am Forum: Technical · Replies: 15 · Views: 847 · Subject: Screeching noise between 15k - 18k near pulleys - 2014 TD4 Alternator overrunning pulley? Aircon compressor pulley bearing? If you’ve checked and replaced the others could be these as there’s only a finite amount of them, But it must be one of the pulle ...  Complete power loss after exhaust disconnected jimbowats 14th Apr 2025 11:15 am Forum: Technical · Replies: 4 · Views: 680 · Subject: Complete power loss after exhaust disconnected Possibly whilst the exhaust was disconnected whilst off road, dust and debris clogged the rear part of the exhaust. Then when you reconnected it the exhaust was completely cloggged causing the engin ...  My 2014 Sd4 GS jimbowats 28th Feb 2025 10:03 am Forum: My Freelander 2 · Replies: 253 · Views: 127250 · Subject: My 2014 Sd4 GS Mine was juddering between 1500 and 1800/2000rpm...wasnt sure what it was but it was eventually diagnosed as a worn torque converter in the gearbox. These do wear apparently and can cause shudder as t ...  ABS Bleeding Help! jimbowats 4th Feb 2025 4:36 pm Forum: Technical · Replies: 10 · Views: 1131 · Subject: ABS Bleeding Help! Ive got a sealey pressure bleeder but no fluid ever comes out the caliper bleed screws... have it pumped to 15 psi but it never works for some reason.. tried it with engine running and also pres ...  Inlet manifold gaskets jimbowats 1st Dec 2024 10:17 am Forum: Technical · Replies: 3 · Views: 534 · Subject: Inlet manifold gaskets  Inlet manifold gaskets jimbowats 30th Nov 2024 11:22 pm Forum: Technical · Replies: 3 · Views: 534 · Subject: Inlet manifold gaskets They are same either side(symmetrical) so can be fitted either way.  Replaced the steering rack jimbowats 4th Nov 2024 7:25 pm Forum: General · Replies: 6 · Views: 2698 · Subject: Replaced the steering rack Bought a re manufactured rack.  coolant loss jimbowats 2nd Nov 2024 6:15 pm Forum: Technical · Replies: 20 · Views: 2453 · Subject: coolant loss Could be EGR cooler? thats above the heatshield above the turbo in the area you mention?  N/S/F drive shaft replacement jimbowats 24th Jul 2024 9:19 pm Forum: Maintenance & Modifications · Replies: 5 · Views: 1730 · Subject: N/S/F drive shaft replacement I changed both driveshafts driveshaft recently , oil will come out as both the nsf and osf driveshaft seals are below the level of autobox fluid in the transmission pan I found that if you undo th ...  RPMs drop at idle and MAP LOW jimbowats 11th Jun 2024 10:14 am Forum: Technical · Replies: 7 · Views: 1933 · Subject: RPMs drop at idle and MAP LOW it may not be your issue but I had a judder around 1500-1800 rpm and it turned out to be a worn torque converter...they are a fluid coupling but also apparently have friction plates which lock up arou ...  Auxillary belt shredding jimbowats 5th Jun 2024 3:54 pm Forum: Technical · Replies: 133 · Views: 17262 · Subject: Auxillary belt shredding Prob got lucky and the timing didnt move when you removed crank pulley and then as you say you were 180 degrees out putting the pins in which made you think it was damaged. If its working fine j ...  Manifold NOW SOLD jimbowats 9th May 2024 12:30 pm Forum: General · Replies: 0 · Views: 399 · Subject: Manifold NOW SOLD sold

Site Copyright © 2006-2025 Futuranet Ltd & Martin Lewis