My r/h headlamp bulb went (non-xenon) so thinking it would be a 5 minute job I popped the bonnet up and started disassembling things!! Am I wrong in thinking this isn't as easy as it should be or is there a simple guide for idiots like me to follow ...please

Last edited by Gecko on 5th Dec 2011 9:10 pm. Edited 1 time in total

In the glove box is a document holder inside which among other things is the owners manual. If you were to take this manual and open it at page 144(MY 2010) or thereabouts you will find instructions on how to change a halogen bulb. The manual describes the process far better than I can and also includes pictures.

If you do not have access to the hard copy manual you can access the on-line version through Topix.

http://topix.landrover.jlrext.com/topix/co...;id=145024 and look under Maintenance.

One side can be done, no problem, the other side is a bit tight, not a lot of room. I'd probably remove the headlight and replace the bulb if I had trouble. Just remember to mark the position of the top bolts holding it on, so you can put it back the same position.

It is a 2 minute job

a) Bonnet up
b) Remove the two screws above headlamp
c) Pull up locking lever
d) Pull headlamp toward you
e) unplug electrics
f) Place headlamp on worktop on a nice clean towel
g) Remove lamp cover
h) Proceed to change lamp

Point F there is VERY inportant!!! The scratch easy

rchrdleigh wrote:

In the glove box is a document holder inside which among other things is the owners manual. If you were to take this manual and open it at page 144(MY 2010) or thereabouts you will find instructions on how to change a halogen bulb. The manual describes the process far better than I can and also includes pictures.

If you do not have access to the hard copy manual you can access the on-line version through Topix.

http://topix.landrover.jlrext.com/topix/co...;id=145024 and look under Maintenance.

Looked in the manual but neither my French Dutch or German were up to the test for this task

EYorkshire wrote:

It is a 2 minute job

a) Bonnet up
b) Remove the two screws above headlamp
c) Pull up locking lever
d) Pull headlamp toward you
e) unplug electrics
f) Place headlamp on worktop on a nice clean towel
g) Remove lamp cover
h) Proceed to change lamp

Ta very much

Add this to instructions.
Note where the washers on the 2 bolts mark the plastic and ensure lamps click into place when refitting. Securing bolts tightened with washers in exactly same place. Alignment then correct. All FL2's (3) Gone
2011 Mercedes C180 CGI Gone
FL2 GS Auto SD with heated leather, factory tints, alloy spare and a few other bits.

Is it really a headlamp removal job to change the bulbs?

Just tried the method as per the manual - pull up the rod things, pull the cover off but on the near side there is not enough room to actually remove the cover enough to get access to change the bulbs.

On the off side the washer filler upper thing is in the way and can hardly move the headlight cover at all.

I thought my Honda Pan Euro was difficult to do!

Thanks.

It is only two 10mm bolts to remove on each headlight and pull the lever

druand wrote:

Add this to instructions.
Note where the washers on the 2 bolts mark the plastic and ensure lamps click into place when refitting. Securing bolts tightened with washers in exactly same place. Alignment then correct.

Assuming that your alignment was correct in the first place  ______________________
2011 Full Fat RR 4.4 TDV8
2012 FL2 SD4 Auto HSE
2013 Kawasaki Versys 650

That was easy but not as easy as the freelander 1 and maybe not by the side of the road though on a dark winters night.

Freelander1 1 Freelander2 0

Thanks!

deleted, not applicable because the job was done

I just changed my headlamp bulb and made a help video for others. Look up my youtube channel :
'comeinhandynow' by googling it. Or see video at this link for youtube :

Great video, thanks for that, welcome to Freel2.com
All you need now is a head cam